TMT-PR4 (G77 - P67-68)
The PR4 remote control from TMT Automation Inc replaces the older PR3-003 rectangular black case with 4 round silver buttons and is used with the same range of swing & sliding gate motors.
It operates on 433 MHz and uses rolling code
G77 - P67 or P68
|Up to $3.00
|Up to $6.00
|Up to $10.00
|Up to $15.00
|Up to $21.00
|Up to $28.00
|Up to $36.00
|Up to $45.00
|Up to $69.50
|Up to $239.00
The TMT Automation PR4 remote control can be programmed to a number of different TMT Automation branded swing or sliding gate motors using the fitted receiver in the gate control panel or the optional external receiver.
This remote features a new design and feel more robust then the older PR3-003 remote which had the 4 round silver buttons. The keyring loop is part of the moulded plastic casing and feels solid.
The TMT PR4 now has an On/Off switch on the side of the remote which helps to prevent unwanted or unintentional activation of the gate while the remote is in your bag or pocket. Turning the remote off will stop the main buttons from operating. It can be switched back on immediatley by flickig the side switch upwards.
In terms of size the old PR3 remote measured 68 x 33 x 11 and the new PR4 remote is pretty similar in over size at 67 x 37 x 11. The buttons on the new PR4 are larger and have raised dots as numbers from 1 to 4 and have a very positive responsive feel when pressed.
Programming this TMT PR4 remote will depend on which receiver unit is fitted to your system so best to let us know when you order or send us a photo and we can advise on how the remotes can be programmed. Please let us know if the gate is a swing or sliding gate. TMT use dog breeds to name many of their gates including the Terrier, Mastiff & Boxer.
With a swing gate the controller is normally fitted in a grey plastic box next to the gate on a wall or pier. Inside this box you will see the control board and these are normally CB16, CB17, CB18 or CB19 and you should see the code printed on the control board. Of course if you are not sure just send us a photo of the control board and we will help you identify which one you have.
If you are not certain that the remote you have is compatible please feel free to email us a photo of the remote and your motor and we will be more than happy to help you work out which remote to purchase.
All our remotes are supplied with easy to follow instructions on how to program them to your garage or gate motor. To ensure you get the most appropriate instructions please tell us the model of the motor you are going to use the remote with in the comment section of the checkout.
We offer a 12 Month Warranty on all genuine remotes in line with the manufacturer conditions, so you can buy your new remote with full peace of mind and confidence that should there be a problem you are covered.
If you have any issues during programming please call us and we will talk you through it. We can also come and program your new remote anywhere across the Perth metro area just select Deliver and Program as your preferred delivery method at Checkout.
This product meets AS/NZS 62368.1 Clause 4.8 Safety Standards 2020 for products containing button/coin batteries.
WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing a button cell battery inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.
If you suspect your child has swallowed a button battery or placed inside any part of the body, immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.
Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.
Please see button battery safety information from the Australian Competition & Consumer Commission (ACCC).
|No. of Buttons
|Remote Programming Method
|LEARN TO RECEIVER
|Visor Clip Included
|YES - INCLUDED
|Dimensions in mm (L x W x D)
|67 x 37 x 11
|CR2032 - 3V
This aftermarket 2 channel receiver is compact and is compatible with a long list of 433.92mhz rolling code remote controls. See the table below for just some of the compatible remotes. Can store up to 100 remote controls. G57 - P71
CR2032 is a 3 Volt battery and measures 20 mm x 20 mm x 3.2 mm Remote controls for garage doors, swing & sliding gates, home security systems, car alarms, central locking systems use lithium batteries. It is vital to select the correct battery both for fit and function of the device. One of, if not the most reliable lithium battery on the market is...
The KP2-4182 is a wireless keypad transmitter which can be used with TMT Automation Inc receivers for a range of swing & sliding gate motors. It operates on 433 MHz and uses rolling code G58 - INCL
The PR7 remote control from TMT Automation Inc replaces the older PR3 and PR4 remotes used with the same range of swing & sliding gate motors or garage door motors. It operates on 433 MHz and uses rolling code W1 - P67 or P68
This aftermarket sun visor clip can be used to hold a number of different remote controls as shown in the photos. A more complete list is shown below. The clip also comes with screws and plugs if you wish to use it as a wall clip to mount the remote on the garage wall. F1
No customer reviews for the moment.